Differences

This shows you the differences between two versions of the page.

--- en:syntec-okura-manual [2020/05/22 00:25]
jay0324 [Operation Pannel]
+++ en:syntec-okura-manual [2020/05/27 00:23] (current)
jay0324 [Electronic Drawing]
@@ Line 1: / Line 1: @@
-====== SYNTEC MT36 Manual ======
+====== SYNTEC MT Series Manual ======
 ----
-===== MT36 Manual =====
+===== Machine Operational Manual =====
+  * {{ :en:en-catalog.pdf |MT Series Machine Specification}}
+  * {{ :en:mt_operational_manual_syntec.pdf |MT Series Operational Manual}}
+<WRAP center round important 100%>
+Please Note: Some chapters from the MT Series Operational Manual are only for the FANUC Controller, therefore, please find the related information through SYNTEC official controller Manual.
+</WRAP>
@@ Line 11: / Line 20: @@
   * PLC Version: 1.05
   * OP Board: 4018T3
-{{ :en:21_series_lathe_operation_manual-en.pdf |Read Controller Manual}}
+  * {{ :en:21_series_lathe_operation_manual-en.pdf |Syntec Official Controller Manual}}
+  * {{ :en:lathe_programming_manual.pdf |Syntec Official Programming Manual}}
 ===== Operation Pannel =====
 {{ :en:21tah-controller.jpg?nolink |}}
 {{ :en:4018t3.jpg?nolink |}}
-<WRAP group>
+<WRAP center round box 100%>
-<WRAP half column>
+  - USB Port
-  - 1. USB Port
+  - LCD Screen
-  - 2. LCD Screen
+  - FMenu bar keys
-  - 3. FMenu bar keys
+  - Switch function Keys
-  - 4. Switch function Keys
+  - Reset Key
-  - 5. Reset Key
+  - Address-numeric Keypad
-  - 6. Address-numeric Keypad
+  - Page Keys
-  - 7. Page Keys
+  - Cursor Keys
-  - 8. Cursor Keys
+  - Editing Keys
-  - 9. Editing Keys
+  - MPG
-  - 10. MPG
+  - Cycle Start/Stop Buttons
-  - 11. Cycle Start/Stop Buttons
+  - Mode Keys
-  - 12. Mode Keys
+  - Feedrate keys
-  - 13. Feedrate keys
+  - Axis Select keys
-  - 14. Axis Select keys
+  - G1 Feedrate keys
-  - 15. G1 Feedrate keys
+  - G0 Feedrate keys
-  - 16. G0 Feedrate keys
+  - Spindle Speed keys
-  - 17. Spindle Speed keys
+  - Spindle Control keys
-  - 18. Spindle Control keys
+  - Not Used
-  - 19. Not Used
+  - Light On/Off
-  - 20. Light On/Off
+  - Lubrication On/Off
-  - 21. Lubrication On/Off
+  - Chip On/Off
-  - 22. Chip On/Off
+  - Chuck Open/Close
-  - 23. Chuck Open/Close
+  - Coolant On/Off
-  - 24. Coolant On/Off
+  - Not Used
+  - Optional Stop
+  - Optional Skip
+  - Single Block
+  - MPG Simulation
+  - Livetool A On/Off (JOG/MPG)
+  - Livetool B On/Off (JOG/MPG)
+  - F1: Auto Door Open/Close
+  - F2: Dry Run
+  - F3: Machine Lock
+  - F4: Air Blow
+  - Overtravel Button
+  - F5: Not Used
+  - Program Lock key
+  - Power On/Off Buttons
+  - Emergency Stop Button
 </WRAP>
-<WRAP half column>
+<WRAP center round important 100%>
-  - 25. Not Used
+//**COMBO Key**//
-  - 26. Optional Stop
+  - C Axis On/Off: JOG Mode -> [C+][C-]
-  - 27. Optional Skip
-  - 28. Single Block
-  - 29. MPG Simulation
-  - 30. Livetool A On/Off (JOG/MPG)
-  - 31. Livetool B On/Off (JOG/MPG)
-  - 32. F1: Auto Door Open/Close
-  - 33. F2: Dry Run
-  - 34. F3: Machine Lock
-  - 35. F4: Air Blow
-  - 36. Overtravel Button
-  - 37. F5: Not Used
-  - 38. Program Lock key
-  - 39. Power On/Off Buttons
-  - 40. Emergency Stop Button
-  -
-</WRAP>
 </WRAP>
-===== SYNTEC Program Manual =====
-{{ :en:lathe_programming_manual.pdf |Read Programming Manual}}
 ===== Custom G Code =====
@@ Line 109: / Line 120: @@
 ===== Electronic Drawing =====
 {{ :en:mt-syn-380.pdf |Electronic Drawing For 380V 6KVA}}
+<wrap em>(UPDATE: 20200527)</wrap>